boats
Articles

Spring Maintenance Tips
February 5, 2013 11:06 AM

Getting your boat ready for the spring is as easy as following these simple tips to de-winterize it after a long, hard winter. If you did winterize your boat, you saved yourself some spring boat prep time and possible headaches now, which means the road between your boat and the water is shorter! Although it is always best to winterize a boat before putting it into storage, if you didn't, don't worry. You can perform those tasks now for the spring commissioning. Here's how:

1. Have Your Manufacturer's Manual Handy
If you have a copy, great. If you don't, it would be a good idea to get one. You'll need it to replace fluids and parts properly. Never take apart anything without consulting the manual first.

2. De-winterizing Your Engine
The engine is the heart of the boat, and since it will most like take the greatest amount of time and be the messiest, start here. If you didn't change the oil at the end of last season, do so now. After running your boat all summer, it's likely that water, acids and other byproducts have built up. It's important to change the oil to prevent corrosion and excessive wear which can lead to loss of power, poor fuel economy or engine failure. At the same time you change the oil, be sure to change the oil filter. Change the oil in transmission or the outboard's lower unit as well.
Next, flush the cooling system and replace the antifreeze with a 50/50 ratio of water to coolant.
Finally, replace the batteries and perform a thorough engine test.
 

3. Inspect the Canvas & Vinyl
Check your bimini top, seats, covers, and other vinyl and canvas items for tears, mildew and dirt. Repairs tears and holes, and then clean with the proper cleaner for canvas and vinyl.
 

4. Inspect the Hull
Carefully inspect the hull for blisters or other chips and cracks as well as for chalky residue. If you find blisters, repair them. If the boat's hull is chalky, it could indicate oxidation. Determine the level of oxidation, and then restore the boats gelcoat to its original luster. Then, throughout the summer, follow a gelcoat maintenance plan seen in attached article to keep oxidation at bay.
 

5. Clean and Wax the Hull
First clean your boat's exterior using a marine safe cleaner from a marine supply store. Then, apply a freshcoat of wax.
 

6. Inspect the Windshield Wipers
Inspect and replace windshield wipers if necessary. If the wipers are in good condition, apply a rubber lubricant to protect them from the harsh marine environment. Some experts recommend stowing wipers until you need them to keep them in good condition longer.
 

7. Polish the Metal and Teak
Known as brightwork, metal and teak enhance the look of your boat. If it's dull, your boat will not have the same visual appeal as it might otherwise have. Also, prolonged neglect of metal and teak can result in pitting and eventually compromise the integrity of the materials and their intended use. To protect the metal, use metal polisher like Never Dull. For teak, it is usually recommended that you sand it and then apply stain and varnish.
 

8. Replace and Test all Electronics
Bring all the electronics back on board and do a thorough test to be sure they are working properly. Test the radio, GPS, compass, depth finder, and any other marine electronics.

 

Remember these tips will help you get your boat ready for the season as well as some tips that if done correctly should limit the amount of downtime during the short boating season. 


 



Categories
Recent posts
Posted: May 9, 2016 3:20 PM Holiday Weekend Getaway
Posted: April 6, 2016 2:07 PM Safe Boat Launching
Posted: March 17, 2016 1:11 PM Spring Maintenance
Posted: February 15, 2016 11:00 AM
Posted: January 29, 2016 11:52 AM Preparing for the Boat Show
Posted: February 5, 2013 11:59 AM Gelcoat cleaning/protection
Posted: February 5, 2013 11:37 AM Gelcoat Maintenance
Posted: February 5, 2013 11:06 AM Spring Maintenance Tips
Tags
Email news
Subscribe to Our Blog:




Click to Print this Page